FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   PreferencesPreferences   Log in to check your private messagesLog in to check your private messages   Log inLog in 
Forum index » Science and Technology » Engineering » Control
To view Sub-station data Locally
Post new topic   Reply to topic Page 1 of 1 [2 Posts] View previous topic :: View next topic
Author Message
Cameron Dorrough
science forum Guru Wannabe


Joined: 09 May 2005
Posts: 103

PostPosted: Thu Jun 22, 2006 10:46 pm    Post subject: Re: To view Sub-station data Locally Reply with quote

"Praveen" <bpraveen2@gmail.com> wrote in message
news:1150977316.786896.128240@p79g2000cwp.googlegroups.com...
Quote:
Hi
In our SCADA system, presently all RTUs report to the control-centre,
and real-time SCADA data is monitored by operators at control-centre. I
would like to know how to further configure these RTUs to report this
data locally also (pertaining to that station ).That is the the
real-time data of that particular substation shall be viewed by the
Local substation people.

Our system details: RTU to control-centre protocol: IEC 60870-5-101-
RTU make : S900 (supplied by ALSTOM/ made by CEGELAC)
Control-centre software: EMP 1.5.2 supplied by ALSTOM, running on Open
VMS Platform.

Thanks in advance for your response.

The easiest way to do this is to connect a local touch-screen display to a
spare RTU comm port on each of the local RTUs. Someone will have to
configure the display to show the data you want.

It should not be very difficult - assuming there is a spare port available
for local programming (and there should be if the system was designed
properly Wink I suggest using Modbus for the local display comms, since this
means you could use almost any vendor you like for the local display - not
just Alstom.

Cameron:-)
Back to top
Praveen
science forum beginner


Joined: 22 Jun 2006
Posts: 1

PostPosted: Thu Jun 22, 2006 11:55 am    Post subject: To view Sub-station data Locally Reply with quote

Hi
In our SCADA system, presently all RTUs report to the control-centre,
and real-time SCADA data is monitored by operators at control-centre. I
would like to know how to further configure these RTUs to report this
data locally also (pertaining to that station ).That is the the
real-time data of that particular substation shall be viewed by the
Local substation people.

Our system details: RTU to control-centre protocol: IEC 60870-5-101-
RTU make : S900 (supplied by ALSTOM/ made by CEGELAC)
Control-centre software: EMP 1.5.2 supplied by ALSTOM, running on Open
VMS Platform.

Thanks in advance for your response.
Back to top
Google

Back to top
Display posts from previous:   
Post new topic   Reply to topic Page 1 of 1 [2 Posts] View previous topic :: View next topic
The time now is Fri Nov 24, 2017 8:25 pm | All times are GMT
Forum index » Science and Technology » Engineering » Control
Jump to:  

Similar Topics
Topic Author Forum Replies Last Post
No new posts modelling method for categorical data Arby Math 1 Wed Jul 19, 2006 12:09 pm
No new posts Obtaining a morphism of sheaves from homotopy data categorist Research 0 Mon Jul 17, 2006 8:15 pm
No new posts with the birds i'll share this such lonely view Dobri Karagorgov Math 0 Tue Jul 11, 2006 3:49 pm
No new posts starting question: analysing the interations of historica... richardchaven num-analysis 1 Sun Jul 09, 2006 4:24 pm
No new posts Fit a transfer function to gain and phase data Roza.Mahmoodian@gmail.com Control 7 Fri Jul 07, 2006 5:05 pm

Copyright © 2004-2005 DeniX Solutions SRL
Other DeniX Solutions sites: Electronics forum |  Medicine forum |  Unix/Linux blog |  Unix/Linux documentation |  Unix/Linux forums  |  send newsletters
 


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0187s ][ Queries: 20 (0.0039s) ][ GZIP on - Debug on ]